The PBCA is having a ride from Rowville to St Andrews this sunday 4th of May, through the Dandenongs and Yarra Valley Hills. Completely cancelled if raining. ...
Hi all just a quick question regarding valve stem seals. The piccie on page 80 of the clymers book shows an exploded view of the valve assembly. Are the valve...
hey ben theres only one valve stem seal mate and thats for the top valve if i remember right cause the bottom valve is actually upside down so the valve doesnt...
Hi all Can any one tell me how to check how much oil is in my front forks, and if i need more in there, what sort to use, they seem to stick a bit when they go...
The forks take 140ml of oil. The easiest way to check is to drain and refil. Because the forks have no damper rod, only a hydraulic buffer for bottoming, I...
The switch on my brake light has busted off and therefore my brake light stays permanently on. Does anyone have a spare Front Brake lever assembly lying around...
Depends on whqat type of switch your after. There are two that I know of. One is an external switch & the other slides into the assembly itself. I bought a...
Has anyone tried the Kenda K760 Trak Master II Dual Sport tires on their CT? They are a little pricey ($34 @ DennisKirk.com) but are DOT approved for highway...
Just brought home a very clean CT90, 1972 model. There is a bolt that goes through the center of frame from the handlebar release lever mechanism to a nut...
No direct answers but some possible causes Generally sticking shocks indicate that there is some foreign matter in the system. This could be dirt, rust cow...
Pete is right - there is only one seal and it's on the inlet valve. The reason is not that the other is upside down. It's more likely because when the inlet...
Hi, I was just wondering what the different types of CT110 are in Australia, and which is better. Is there any difference between the ones that Aust Post uses,...
hey guys, i brought a ct 110 89' yesterday & it was running perfectly then when i woke up today to ride it it wont start or even think of starting??? i know it...
hey guys, i brought a ct110 89' model bike yesterday and it was working fine yesterday until i woke up and the bike now doesnt kick over. i am sure everything...
check under the spark plug cap for moisture spray some wd40 in it then check to see if ya air cleaner hasnt filled up with feul as when they flood the feul...
postie bikes dont have the h/l range thingy only the farm modle has that and if ya have it in low and ya flog it ya will go slow and kill the bike regards pete...
My CT90 did the same thing. Very possible it$B!G(Bs varnish in the carb and will require a thorough cleaning, particularly if it sat for a long time. Could...
180 out on the cam timing valve hit piston ... _________________________________________________________________ MSN Instant Messenger now available on...
This is interesting, It makes sense for the seal to be on the inlet valve BUT of the 3 heads I have here, 2 spares and the one on the bike in question, all 3...
Dear All Is it possible to remove the entire original air intake/cleaner setup (from carb to rack) from a CT110 and replace it with a small, more efficient air...
Ben, If your good postie engine is ok, don't pull it apart.Only do it when it needs it. If you go to the Honda spares supplier for the seal, their microfiche ...
More evidence of just one seal. Look in the files section of this postiebikes usergroup and you will find a file "ct110parts.zip"(thanks to hqgrace)....
the best tool in the shed is patients and us ur head start with thas basics is it getting fuel is it sparking work opuit whats wrong and go from there the...
how much will a head gasket kit and a set of rings cost (geniune and non genuine) ... From: Ben To: postiebikes@yahoogroups.com Sent: Wednesday, May 07, 2003...
Hey Guys, I am Kinda New to This Group and i have got myself an '81 ct110 (i think) and it isnt in the best of conditions, the Exhaust is rusty and is not...
