If you had the needle screwed all the way in sounds like trash not leting the needle seat pull the needle out and check for trash ..you can also take the...
My wife was gracious enough to buy me a lincoln pro mig 135 welder for Christmas. I am going to take a shot at building an off road kart. I have looked at the...
try removing your float -dry it off with a rag and blow compressed air over it if there is any fuel inside it you will see it get slightly wet a small amount...
it doesnt have a float. ... air over it if there is any fuel inside it you will see it get slightly wet a small amount of fuel inside this will cause huge ...
The Edge makes a vehicle called the XRV that is designed to be used with an industrial engine. It is a little heavier that what you want to do and it uses rear...
i need a cheap tubing bender does anyone know where i can get the best deal on one either hydrolic or mechanical? that and a few more parts are all thats...
Cheapest way to go is to rent one or borrow one. What size tubing? The hydraulic frame benders would do fine. If you can't rent or borrow then look at ebay for...
harbor frieght carries them. they have a12 and 16 ton for around 100$ up to two inche dies for bending.<A HREF="http://www.harborfreight.com/">Harbor Freight...
well, i got that sob crankin again, new plug, and diaphram and gas. ... compressed ... be ... be ... <no_reply@y...> ... That's ... would ... to ... that ... ...
hey you all, I need to ask you all to say prayers and ask for a mircle for my dad, he's in the hospital dieing of prostate cancer, he was doing good this...
I'm thinking sand paddles would be effective in the snow. I can't see any regular type ATV wheel being effective, the dep treads would just clog with snow. ...
Why would u want to have a tubular rear axle. I know they weight less but i thought they would not be able to to hold up good offroad. If you are using a...
The Edge Sidewinder uses a chromemoly 1-1/4" diameter rear axle. I haven't heard too many stories of people bending them. Those kart axles are really quite...
yea i found that out the past few times it snowed, i couldnt make it up the hill more than half way, but it is fun anyway. ... see any regular type ATV wheel...
i do believe i need a new carb, no matter what i do the engine will not tune at all. If you take the gas flow adjustmment screw out it runs the same as it...
could be a valve, does it have good compresion? take the head off and look at the valves. ... From: frostedice2 To: offroadgokarts@yahoogroups.com Sent:...
oh i see now they are chromemoly axles. that makes a more sence now. I thought you would be used reg mild steel. got ya now. But still if they had solid axles...
Actually the chromemoly tube axles are a lot stiffer than the 1" solid axles. I haven't seen 1-1/4" solid axles, but I guess they could be around. I don't...
the valves apear to be fine, but it fouls up plugs pretty darn fast ... and look at the valves. ... will ... it ... its ... <no_reply@y...> ... gas. ... ...
hmmm, The piston might be shot? Does it have good compression? if you put yor finger on it does it move back and forth within the cylinder? If it does your...
well then what are axles on racing four wheeler made out of. They must be made out of something very strong b/c they span out like 10 or 12" with out a carrier...
no, its not burning oil at all, its just running very rich, because the oil level never goes down, and there is no play what so ever in the piston. and you can...
I would try a new carb then, maybe a new ignition coil to. ... From: frostedice2 To: offroadgokarts@yahoogroups.com Sent: Friday, January 03, 2003 3:48 PM ...
... using gas mixed with oil.That will cause everything you are describing to happen. In offroadgokarts@yahoogroups.com, "connie crossan" <ckcrossan@n...> ... ...
no, but i am using low octane gas like 87, im going to try like 91 and see what happens ... accidently ... <ckcrossan@n...> ... can ... head ... screw ... ...
I raced go-karts for several years and have never seen a bent 1-1/4 axle. And I have seen some pretty bad wrecks. the tubular axle is stiffer because it is...
froste, if it is a briggs motor, try taking out the mixture adjustment screw, there should be a 7/16" or 1/2" nut that holds it on, then take a flat head...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
