Hi, I am still looking for opinions on these axles, are they junk or could they be used yet? My first thought was junk but I have heard from a few guys in our...
2nd part of your response is just like you said,,,just kidding. If that were to happen (switching axles side to side) it would snap the axle as it tries to...
I used the stock Cub bearing cups, The left side one has the bearing race moved over much farther than the right side, also the left bearing on the carrier was...
... of ... 2 ... two ... with ... a ... to ... wearing ... bearing cups that come out right behind the race so I can put a punch in the holes to get the race...
Great photos and write up. One question. Would it work to try and center the diff in the cub rear end to try and get the axles to be the same length? By...
I had the idea that could be done, but I think the diff would have to be moved .250 to center the pin so the axles would be the same length, 1/4" off long axle...
The whole purpose of a flywheel is to give the engine its grunt force to keep turning right???and to give it some balance right???Could you say move the...
Hi John, There are several automotive applications where this takes place sorta'. In the early 60's Pontiac built a "Tempest" that had a transaxle in the rear....
... <rkawilson@...> wrote: John I don't see why you couldn't make it work. If it were me I would run the driveshaft off the pto side of engine and flip the...
Hi, Do you think its possible to keep a heavy flywheel tight on a straight shaft? Some day I want to mess with building a alcohol burning OHV Tecumseh, My idea...
Well my goal was to build a 14hp Tecumseh up, and have the billet flywheel made to hook up the after market clutch drivers to it...This way I can run the...
http://img.photobucket.com/albums/v313/TomW/corker.jpg Hi, Here is my old Cub stock class tractor with a OHV Tecumseh in it. So far I have only ran it at our...
But do you guys Honestly think this would work???Because if you guys think it will work, Im gonna start investing money into making this work...I had a quote...
Ok, everyone knows how hard it can be to find the "hard to find" parts for their tractors...But how much easier would it be if their was a group that had alot...
I am looking for some info on this tractor. There is no tag on this tractor. Front, and rear is cast iron. The fenders are round. There is no motor in it. I'm...
... is the tractor a wide or a narrow frame? that could help you out alot and narrow your searching area down. it could be a 70,100,72 or many more and some...
Yes. As long as you're "qualified" to do the welding, machining, etc. GO MAN GO! Take note of the comments offered. If you are putting it on a straight shaft...
I can weld it, but I gotta have a buddy of mine do the machine work (should be fairly cheap)...The flywheel would prolly be out on the end and I thought about...
I am looking for an adapter to put the clutch 6 pin driver over onto the pto end of this 25hp liquid cooled engine. The flywheel end is driving the water pump...
here's a photo of a dandy pto drive/clutch hub adapter on Vogel's spline drive clutch made by Frank Edwards (photo of 82 series spread frame Cub), his son Greg...
for sale 126 cub. 14hp s/a. very strong puller.three pulling gears,locked rearend,30 over engine,brilet head,midwest crank and rod,20 lb steel flywheel,alky...
OPEC sells oil for $136.00 a barrel. OPEC nations buy U.S. grain at $7.00 a bushel. Solution: Sell grain for $136.00 a bushel. Can't buy it? Tough! Eat your...
I belong to a club that is just geting started here in Minnesota. We need to set up some by-laws or a constitution as it would be. Does anyone have an...
All other engine specs being equal, the regrinds (Vogel, Lakota or whomever ), will outperform the 18 hp cam. Usually by a very noticeable margin (We've seen...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
