There are 114 members on this group. Two very senior Formula Vee drivers/engine builders/car builders post emails regarding concerns about legalities...
Would I be correct in saying that a Ball Joint front end would have put the old debate of angled/worn link pin bushes to rest not to mention the fact that it...
Funny no one has mentioned the introduction of the government ruling that was to come into effect as of Feb 1 2003, regarding asbestos brake products........
Damien So what are you doing? It doesn't mean that just because you are not be concerned, Formula Vee should not be. Consistent interpretation of rules, and...
If these new brake pads (and shoes) are anything like the LRP, stay well away! I recently helped strip a BMC A Series engine that had done only 40000miles on...
--Phil Funny you mention the asbestos now you will open a can of worms-. Just to let people know this was all disscussed quite some time a go and was part of...
Ian Chivas
IJCPLUMB@...
Feb 4, 2003 9:29 am
887
I have recently made a new exhaust in mild steel for my car. I wan't to get it coated in ceamics,however I don't know of anyone in Sydey that can do this. Does...
Daniel, Charlestone Exhausts in Blacktown did this about 2 years ago.I'm not sure but I think they may have just sent it to Melbourne to be done. Try them or...
Gday All.... Just wondered if anybody has an Iceman dash system in Melbourne area (the further east the better) that I can test a faulty unit against.... Ive...
Gday Phil, The beam sender's signal comes out with a flat sort of triangular shape. i.e if it is on its side it will send on the horizontal proving to be...
Thanks David, sound like you have had some fun setting these up before, the unit I have here is of the older type, I did find that there is a period of time...
As can be seen by the following pics, the recent Motorsport Show in Melbourne was a great success, well done to all involved... Looks like another busy year...
Hello all The date for the 2003 Nationals has been set - to be held at Baskerville over the weekend 18th & 19th October. This looks not to clash with other...
Daniel and Tracey Jel...
pitlane@...
Feb 25, 2003 11:13 am
894
Hi Danny, Great to see a date is confirmed. Do you have an understanding on the race format and program as yet? Will 1600 and 1200 cars be running in the same...
Hello Gary & all Sorry not to get back sooner. I cannot answer your question at this time, the use of the 1600 engine in each state is to be determined by the...
Daniel and Tracey Jel...
pitlane@...
Mar 5, 2003 10:46 am
896
Hi Danny & All, In my opinion, the Nationals is the pinnacle event on the FV calender. It is the responsibility of the FVAA to support the category as a whole...
Gary, I'll try to stay out of the debate as much as possible but for my two cents worth I don't think that we should run a combined race if it ever came to...
I agree with David unitl 1600's are nation wide there is no point in having a nationals for them. Stephen Butcher ... From: <djcutts@...> To: "fvee...
Stephen Butcher
sb@...
Mar 6, 2003 12:03 am
899
Does anyone have the entry/supp regs to Sandown? I don't think I've made it onto the mailing list yet and can't find an entry on the VMRC website. I would...
Hello all Here at last is the CAMS Bulletin for the Formula Vee Tech Regs as published today by CAMS. These regulations are now in place. There is much...
Daniel and Tracey Jel...
pitlane@...
Mar 6, 2003 9:02 am
901
Got them now. Thanks everyone ... I've ... VMRC...
... The rules are as such if your car has change to suit the requirements you meet the new rules end of story. ChivoOriginal Message ----- From: George ....
Ian Chivas
IJCPLUMB@...
Mar 7, 2003 8:53 am
904
Hi George All of the "new" rules are optional for existing cars (except minimum weight increase), therefore if you comply with existing rules now you won't be...
Andrew Brown
asb1969@...
Mar 7, 2003 8:42 pm
905
Morning all: Question regarding the bolt that has to be glued into the left hand stub axle....which end is it meant to be glued in? i.e. from the outside of...
John & Susi Murphy
murfberg@...
Mar 8, 2003 12:15 am
906
Inserted from the inside. ... From: "John & Susi Murphy" <murfberg@...> To: <fvee@yahoogroups.com> Sent: Saturday, March 08, 2003 11:07 AM Subject: Re:...
Daniel and Tracey Jel...
pitlane@...
Mar 8, 2003 7:11 am
907
The release of the CAMS Bulletin means the regulations now apply. Danny ... From: "Andrew Brown" <asb1969@...> To: <fvee@yahoogroups.com> Sent: Saturday,...
Daniel and Tracey Jel...
pitlane@...
Mar 8, 2003 7:19 am
908
a.. Disc brakes, side impact and upgraded roll over protection is compulsory on new cars first log booked from 01/01/03. Are there any NEW cars out there that...
the bolt would need to be approx 135 mm long which may prove hard to find in 8.8 hi-tensile however, your suggestion makes sense and would not affect the...
