Here's a link to a free audio article on measuring Black Powder: http://www.striperadio.com/survival/measurebp.htm All listeners need is Windows and...
I will soon be receiving a Plains pistol kit in .50 cal. I would be interested in the powder load for target shooting with round ball in this one! Also,...
A 32" barrel? Does that come with a full-length stock, including butt? I believe my GPR has a 32" barrel... -Kees- Muzzleloaders@yahoogroups.com wrote: The...
Yes it does... I bought the kit from J C Penneys about 33 years ago... The only identification on the whole thing is the word, "Spain" on the barrel. It has...
... If the nipple can be removed I would think it would be a pretty simple task to reduce the hole size as long as the rest of it is OK. -- "farmer" Just when...
Whoops, I read your original post to say it was a pistol kit, which is why I questioned the 32" barrel. My fault. Good luck with building it. You might want...
Hi Kees. I was beginning to wonder the same thing- haven't seen a good technical question in two weeks! I've just been building guns, trying to get this last...
Gary and I each bought a Lyman Plains Pistol kit recently. We have been shooting a lot and I have been pretty busy builting the pistol kit. Thus far, I'm...
Don't know where everyone is, but I'm still here. Richard S. Halliday "hodgdonh110" <A HREF="http://groups.yahoo.com/group/PSEArchery/">Yahoo! Groups :...
Spring has sprung! Maybe everybody is out shooting. Rendezvous last weekend. Today is the monthly club shoot here in Yolo county CA. Has any one attended any...
I'm quitting. Thank you those who were very helpful, and good riddence to those of you who use this forum to ostrisize and vent your own insecurities. I will...
... Gee, nothing like being singled out for honorable mention... :-) The rest of you guys that pissed him off will just have to wonder if he was talking...
I will be ordering a Lyman Trade Rifle soon and want to install the 57 sml receiver sight and the #17 front target sight. Has anyone dealt with these? Does the...
... responding... so what gives? ... I just went back through the messages and didn't see anything from you since your posts on the Kentucky kit. Was that the...
... The #17A just taps into the dovetail. My Lyman catalog says "57SML fits perfectly on Lyman Deersalker or Trade Rifle. Other models may require minor...
Hi Kees, The front sight on the Lyman drifts out to the right if the muzzle is pointing away from you, reverse to install. A little 3in1 oil helps. The tangs...
... the muzzle is pointing away from you, reverse to install. A little 3in1 oil helps. The tangs on the new Great Plains rifle are already drilled and tapped...
That brings back fond memories! I often shot a Hopkins & Allen Underhammer with a peep sight in my younger days. That was a very sweet shooting rifle. I seem...
I must like it, because it is the one rifle I haven't sold or traded of over the years. I bought it in 1968 from Dixie Gunworks. The only problem I have with...
... Isn't it funny how we often fail to give proper attention to stuff in our own back yard... Deer Creek which has a Waldron mailing address is actually...
I got my new Lyman Trade Rifle delivered by UPS Friday and bought various shooting supplies from a local shop. What they did not have I ordered online from...
My GPR came with the adjustable sight and a "primitive" non adjustable one. I was dissappointed with the quality of this rifle compared to one I bought 6...
I like the quality of the gun overall. The only rough spot is on the bottom edge of the butt stock. It does not mate up entirely with the brass furniture of...
The height of the 37 ML is .445". The 17AML is .494" but the catalog doesn't say how high the 17AEU is. It also doesn't state the adjustment range of the...
I got a Lyman brass tapper hammer with a brass drift and will use that to tap out the sights. I am thinking of cutting the sight off the original rear sight...
I clean my flintlocks with a combination of the hot water with detergeant method and the commercial blackpowder bore cleaner method. I first use a brass brush...
Hi Robert, I think it is the bore butter that is showing up on the patches, as everything else is the correct method for cleaning. I recently tried a free...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
