You have to take the clutch cover off of the engine first (the left side cover as you're sitting on the bike). Look at the picture I'm attaching. There's a rod...
Carl, Thanks, that helps. I have a scrap set of engine cases where the idler shaft was spit out of the top of the engine, and I'd really like to avoid that....
I have a 400 size engine that looks much like my 74 wr400 except that it has no engine #plate(no holes for rivets), nor any marks in the case above the fly...
thanks Chuck ,i just bought a new cable and the cable appears to be to long so i am going to try and get slack out your help is most appreciated thanks bill ...
Remember Bill, do NOT take the kickstarter arm off. The clutch cover comes off with the kickstart assembly attached to it. It's another tricky job to put it...
i do not see how ajusting will take out all the slack i have, its seems already adjusted right,the levers move 9 mm when i pust it with screw driver chuck...
Bill, The engine came out of running bike before it was parked as I mentioned to you before you purchased it from me. Are you using Magura levers? This makes...
bill klemme 201 east 9th ave ,Apt 115,Anchorage Alaska 99501,yes i got a new cable for it ,it might be to long and i put a magura lever onto the stock perch...
You shouldn't have to "push" it with anything. 9 to 13mm of freeplay, or free movement, is what you need before it starts to disengage the clutch. The...
I am soooo confused. what the heck are you all doing? please measure the overall length of the cable and the outer jacket on the one that "works" with this...
me too,i am checking now to make sure i have the right cable ,this one is 49 inches long,this is the first husky i have had so figuring out as i go happy 4th ...
Has anyone tried any of the aftermarket pipes available for the 76 cr/wr 250? Which makes the best power? How does it change the powerband? Thanks Steve...
I've got a 2000 KTM 400 SXC, which is a LC4 powered-4 stroke , street legal enduro/dual sport/dirt Bike, it's a true dirt bike Not some overweight XR or KLX....
Bill, Did you ever get that clutch sorted out? From: bill klemme <naptman1@...> Reply-To: HuskyOwners@yahoogroups.com To: HuskyOwners@yahoogroups.com...
the cable that i had bought did not have the nut adjuster on it finalley got the right cable that has that adjusting nut and it worked thanks chuck smith...
gs1000, Not sure if you think we need a laugh or you just wish to be funny because this thread bugs you, but I know this thread is very important to Bill. Bill...
a little humor, that's all. I even suggested to Bill to check the two lengths and be sure. I have been there and done that. it sucked. other vintage faithful...
gs, Sorry, it just did not read that way ....and this is the problem with email. AND, I forgot about your helpful hints. I am just a bit closer to this issue...
I picked up a 430 last month and have been going over it slowly but surely trying to at least have it ready for Redbud's Grass Race in October. The rubber...
Try searching the home site of this group; http://sports.groups.yahoo.com/group/HuskyOwners/?yguid=168936303 I tried to do a search, but something isn't...
Hello Everyone. I uploaded what I think you will find as a rare look at two 1970 Husqvarna 400 Cross that I restored at the same time. One of them now resides...
Hey Guys, Just sold my 2000 KTM 400, & it's time to further gain back some much needed garage space. So with that I'm selling my 1979 Husqvarna 390 OR Some one...
Thanks Bob. The photos are not high resolution at yahoo so you can't appreciate the true quality of the bikes. The bike are as true original as I could get...
I'm just curious. What ever happened to this bike, Curt? Did you get it running? Did you sell it? If you sold it, did the buyer ever get it running? If...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
