Buddy, It was Motocross Action, August 1982, pages 40-42. It was the "centerfold" and looked like an 82 in an 83 frame. The tank was gray with black trim...
This spacer looks like a big fat washer, correct? And the bolt that holds the damping rod goes through it, right? And it came out of the very bottom of the...
Craig - how about scanning and posting in the files section? regards, Steve ... that holds ... very bottom ... and matches ... then comes ... section ... it to...
Hi All, I need to get hold of a sprocket puller for my 72 125. Craig C has them on huskyclub but I have had no reply from him recently. I was wondering if...
Use a three jaw puller available at Sears or a good automotive parts store that also carries some tools. Sometimes they are called steering wheel pullers. If...
Hello John, Thanks for the advice. I bought a 3 legged puller and attempted to remove the splineless sprocket. I cleaned up the area and lubricated it with...
That is not unusual on this type of sprocket. The standard Husky puller also will pull teeth and the ears break off as well. Best advice is to do this SLOWLY...
Thanks for the advice John, as you may have guest I am not much of an expert on these bikes (or any others for that matter) but i want to work on it to fix my...
Throw the old tranny away!!! The one out of the 175 most likely is one of the splined type and is a better tranny. The one you have is ball indent type on a...
Hi, I bought most likely a 125 from ebay. It has a radial finned head painted black like my 1976 175 GP, but the round part that sticks out on the rear of the...
Dave, To repair your drainplug threads, you might want to just tap it to a little larger size. I've done this using a magnetic plug I got at the local auto...
John ; You could tell the displacement by pulling the head and measuring the bore and stroke,but I'm not sure how to determine the yr. of production...Kerry...
The tag onthe right side of the engine will tell what size and year of manufacture as well. Huskyclub.com has an information page for this info. John H...
I just picked up an 84 510 TE, with only 1200 miles. It has the usual failure of the original SEM magneto. After fooling with it enough to get really...
Did you read post # 413?,John says the i.d. tag is no longer attached to the motor! what would you do next? Oh by the way, on black leg 4 rib forks the beveled...
I was cleaning out a closet this past week and found a flyer from an individual making Husky tools. Clutch pullers, sprocket puller, case splitter, piston pin...
I'm with John on this one. Unless you're going for originality, use your old one for parts and use the newer shafts and shift mechanism. I did. It does work...
... John, Good luck, the # is: 249144326. I bid on it as a 250 which is what he said, then he changed and said it was a 125, too late I was high bidder....
Any ideas on how to deal with worn husky brake drums? I put new shoes in and the adjustment is almost gone. Someone told me you can shim the shaft they rotate...
Check with Vintage Brake http://www.vintagebrake.com/ They do new drum relining and should be able to help. Dan Message: 5 Date: Mon, 08 Nov 2004 00:57:28...
Another approcah - if the drum is still round and seems OK, you could leave it, and instead go to thicker brakes shoe linings. Vintage brake can do all this,...
I have an '82 wr430 and was checking spark and noticed spark 3 out of 4 kicks... ideas? Coil? Cap? Ground? Will the '81 420 elec.'s work on the '82?...
when was the last time the bike ran? trailridernut <ernz@...> wrote: I have an '82 wr430 and was checking spark and noticed spark 3 out of 4 kicks... ideas?...
Hello all, I am still wrestling with getting the drive sprocket of my 72 Cr125! The 'sprocket is splineless' and sits on the shamfered shaft, unlike later...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
