Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the HuskyOwners group. File : /Freeing a...
HuskyOwners@yahoogrou...
Dec 1, 2006 8:30 am
3292
Thanks for the advise guys, I forgot to mention the bike came with a set of 81 WR 40mm forks, so I'm ahead of the game there. what's a good fork seal to use...
I don't know if they are still available, but back then I used fork seals from a Kawasaki KZ1000 on my '81 CR250. They lasted much longer than the stock seals....
17 to 18 inch conversion - the only problem with 17s in my opinion is tire choices - if the wheel needs to be redone then I'd convert but if not and you can...
Soup, What is the best way to radius the hub? How do you go about arcing the shoes and how do you check that you have done this correctly in that you are...
Rick Horvat 330-995-0245 He can fix you right up for about anything Husky. ... From: larry grant To: HuskyOwners@yahoogroups.com Sent: Friday, December 01,...
He is in Ohio and has a real job but specializes in all things to do with Husky's and has had all kinds of discontinued pistons reproduced for many different...
I have a 1982 250 XC Huasky that I finishing up a semi resto/rebuild for trail riding and am having carb issues. Starts 2nd kick cold, runs clean for a few...
Don, What needle do you have and in which position is the clip located? Tom Don Barton <dwbarton@...> wrote: I have a 1982 250 XC Huasky that I finishing...
I had a lot of carb problems with mine using stock Husky parts manual for jetting. It was way too rich until I went to the Sudco website and used their stock...
Also it's possible your coil isn't putting out enough juice to fire under compression. I replaced my coil with one from a company called Flanders. I posted a...
Don, It could be a # of things....Float level toooo high, bad needle and seat....Is plug wet from gas or oil ? Left side seal could have been damaged in...
Not sure what needle, but assumed whatever came when bike was new. Second notch from top. Thanks ... located? ... resto/rebuild ... runs ... main, ... air ... ...
Float is set at 17 mm. Have not checked the needle and seat. Shoulda done that right off. Wet from gas. Appears the seal is OK. I am assuming the rebuild was...
Mikuni carbs that were made for Husqvarna have considerably larger jet numbers than their standard Mikuni counterparts. The air passages inside the carb would...
Don, The ground wire is a very good idea.It's motoplat's most common problem. Also you might try removing the coil under the gas tank and cleaning the mounting...
In painted the frame and before reassembly I took the paint off of everything that even resembled a possible ground source. I did not get to the ground wire as...
Anyone have any problems with mig welding extensions to the chromoly pegs? Also, are the studs at the bottom of 40mm fork legs some sort of wierd thread pitch?...
Okay, I took the motor out of the bike, and stripped the cases down pretty far today, putting everything into a plastic tote for later. The piston actually...
My $500 CR250 is getting sorted out, starts second kick, and seems like a good solid bike. But I'd like to make some mods to make it more suited for the trail...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the HuskyOwners group. File :...
HuskyOwners@yahoogrou...
Dec 3, 2006 2:50 pm
3319
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the HuskyOwners group. File :...
HuskyOwners@yahoogrou...
Dec 3, 2006 2:51 pm
3320
I hope you guys don't mind but I got bored this morning and uploaded a few copy's from Jan MXA articles. If the group likes I can do more. Scott ... Have a...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
