Does anyone have a diagram or an explanation of how the front roller guide spring is installed on the swing-arm? One spring end goes on the roller arm, but...
What is a good starting point for the 40mm fork. They came off a 1983 510, and I have installed them on a 1979 CR250. Started with 5.5 inches of oil...
My 1979 CR250 came with no kill switch. Any suggestions for wiring a two wire kill switch to the Motoplat coil. There are two plugs on it. Thanks, Peter...
I posted an article written by Steve McQ in the files section of the group's home page. It's from a 1966 Popular Science magazine, titled "What I Like in a...
Peter, Jay at Hall's Husqvarna told me to put in 470 - 475 cc's per leg. Wt is dependent on rider wt and preferred feel. I wouldn't recommend adding any air...
I'm not a suspensikon expert, but if it were me, I'd try dropping the oil level in half inch increments - if after a couple of tries, nothing has changed, the...
Dayum Carl - where you bin boy? gimme a call sometime - we need to go riding/racing ... Wt is dependent on rider wt and preferred feel. I wouldn't recommend...
The set up all depends on what kind of riding you are going to be doing. For PV motocross we run 15wt oil at 450 or so cc's which is about six inches from the...
Do I need to scan in the Aughust 23. 1971 issue of Sports Illustrated with the famous Steve McQueen cover? He's riding a nice 400 Cross on the cover. I bought...
On my 77 CR390 76 auto the other end of the spring hooks to a tab welded to the rear brake rod.... unless I am looking at the wrong thing. You are talking...
Jeez.... could you also include the replacement of the shift lever bushings and linkages in that same cover? I need to replace my bushings and our Husky...
Two wire kill switch? On both of my bikes the kill switches ground out the ignition system through the handlebars. Both kill switches are wired to blue wires...
Peter, 2 Wire kill switch has one wire going to the ground and the other wire going to your hot lead coming out of the coil. Make sure the ground wire makes...
The '79 CR250 did not come with a spring loaded roller and arm. The chain guide is a fixed block close to the swingarm pivot through which the chain passes. It...
Matt, It looks to me like a 1980 CR or OR. I'm guessing that it's a 390 or started life as a 390, but can't be sure. The open class bike was still a 390, not a...
... wrote: Matt, If you post the Frame # (In front of the Tank on the RH side) and the Engine # (above the front sprocket) this would help..but as it stand ...
I would kinda' like to read that one Jon. I tried several settings on my scanner to get clear scans with a small file size, 'cause my pages were a little...
Hi Matt, It looks to be a CR frame, '78/79 tank and can't quite tell fin counton cylinder, but generally, 6 fin-175, 7 fin-250, 8 fin-360/390, 9fin-430, 10...
You should be able to decode the model by the frame and engine numbers on the bike. You can match the numbers to charts located on www.huskyclub.com Jon ... ...
The frame is a MM series frame with what seems to be an original swing-arm. It has both the roller guide and the chain slider guide bolted to the back of the...
I counted the fins and came up with seven but then noticed that there was another bottom fin that was black, which would make 8. But there may also be a top...
Hey folks - feel free to post photos and files over at our overflow area at http://groups.yahoo.com/group/HuskyPhotoArchive/?yguid=193323756 Steve In...
Hey I posted the Sports Illustrated article in my picture account under jons77husky. Make sure you click on the View Large icon so you can read the article. ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
