I have had that same trouble before also. Here is the trick that I used.I removed both swingarm nuts and stacked a bunch of washers on one side to leave enough...
I belong to Vinduro also but I have never made it to one of the rides. I go to the Mid-Ohio Vintage Days every year and thats a great weekend of old bikes and...
If you are lucky, you can remove the swingarm bolt with WD 40 and a rubber mallet. However, my experience over the years is that these bolts don't come out...
Robert, I would replace bushings and the swingarm pivot bolt while you're at it. If the bolt has been in there since 1972, chances are it's not going to come...
I have a 72 WR 450 that I am taking completely apart to do a cosmetic restore. Will be a rider rather than show. I don't have any manuals so I'm flying blind...
Hi Mark, Welcome aboard!! I ride old Husky's as well...'76 WR-250 and CR-250...Many of us here are members of the Vinduro Group as well...A group of ISDT/E and...
Im a new member here and I just wanted to say hi to you all. Im a true husky nut! I own 13 bikes and have rode almost all of them.......so far. When I get this...
Rick; I've heard of some people doing that, I cut some off of the carb bell and with a little sand paper it will slide inside of the airhorn. I then mock it...
Does anyone remember the o-ring trick whereas you machine a groove in either the carb bell or airbox bell to allow the fitment of a large o- ring that helps...
I have a complete 1973 250 wr motor, the motor seems to have good compression but it will not shift. The guy I got the bike from said he had the motor apart,...
Hi Adrian, $800, I think the seat height is 37", I will have pics available shortly. I don't know exactly what the susp needs, I purchased in May with the...
I'm looking for a right side shaft for the crankshaft assembly. Part # 16 10 868 01. Does anybody know where to get one? Also need a connecting rod(125mm)for...
Tom, Go with a 2-wire kill switch. A 1-wire switch will not ground if you are using aluminum bars. Also the rubber covered switches are better with keeping mud...
Just got my CR460 fired up for the first time in 14 years, thanks to a carburettor I picked up in the UK last week. Nearly deafened myself!! I noticed a...
Tom; If your 400 is like mine, you have a Motoplat. Connect your kill button to the large blade on the coil or the blue wire. Get ya a good 2 wire kill...
Tom, I wired mine by attaching the kill switch wire to the wire coming from the points set. Just crimp, or solder(better) both wires into one female spade...
How much? Do you have any Pictures ?Does this bike have a really tall seat Height ? What is the seat height ?What exactly does the suspension need ? Thanks ...
Hello all, I am looking for simple wiring instructions for wiring up a kill switch on my 74 400cr. The concept seems simple to me, but the bike did not have...
Go to http://www.uk-motoplat.com/motoplat.htm or http://groups.yahoo.com/group/vinduro/message/5676 and follow the advice given there. It might save you a...
Does anybody have a wiring diagram for a 93 WR 360? How about Ohm readings for the ignition? I believe there are three wires coming out of the stator Blue,...
Call pVp Cycles at 1-888-634-4949 and talk to Andy or 1-760-744-8052 and John will hook ya up...Both of these guy's have anything you could possibly need.Andy...
Hi, I think Husky Club will only want to sell you individual parts lists as printouts for $25 Can supply CD of 66 to 79 parts lists for $3 Nut does not come...
Rick, I'm currently going through a carb dilemma. Got a 75 CR460 minus carb, have bought two carbs which proved to be wrong ones and yesterday hopefully got ...
Anyone out there running a 250 bolt together? If so, what carb are you using? I thought I was being so clever and had fabbed my manifold to fit a later model...
Peter, Thanks so much for the reply. I've sent a note to huskyrider about the parts lists on CD so that in the future I can know part #s to ask for. Does the...
Hi, What you show is nut 12 25 382-01 with the grubscrew that goes through it. Have the nut in stock (new), price is US$3.00 Peter Worrall Husky Parts,...
Folks, I went in tonight to replace all clutch plates on my '72 WR 450. They actually weren't that bad and the basket looked fine. Went ahead and replaced all...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
