I am looking for specific information about the aluminum flevo seen on Erik Wannee's site under 'special material use'. Specifically the seat. Erik's site says...
Once again I'm working on my modified flevo racer, and have been building my own seat. (The seat needs to be able to split into two pieces: a back rest...
Hi John! ... Uhm, what about the Bodylink-seat which is produced by HPVelotechnik? At least is has the "splitted" design, but the side support seems to be...
Thanks for the information, and link. I have seen the HPVelotechnik split-seat, and am familiar with it's design. Nice to see that it actually weighs less...
... Not im my experience. I prefer to put 15-20 mm (0.6-0.8") rubber foam on the original hard Flevo seat shelf. This makes the seat a bit soft and comfortable...
... Very well. ... No, it's not cool. There is too much air (or other gas) inside the rubber so that it works like a thermal shield/thermal isolation, i.e. the...
... One more thing: the sweat flows into a pond at the lowest point of the rubber foam. It's good to drill a hole through it and the seat and put a stiff pipe...
... The usual seat reaches high enough for average people. Just make sure that your shoulders do not reach above the seat. And make sure the seat is in this...
... No! You can't have that much muscles and -- sex organs? More than one? Indeed there are some remarkable findings. In the end I wouldn't remove so much from...
I agree that the flevo seat is well designed. But I am working a version of a flevo racer which converts to standup bike, and the seat performs multiple...
I trying to find out if it is posible to use an Sram 7.0 esp gripshift set with a Shimano 105 front draileur. I have already the gripshifters so i need the...
... I used them for some time on my Flevo. Either I shift or I sweat too much, so they felt slippery and they did hurt my hands, kind of peeling away the skin,...
I am not trying to be a wise guy, but wearing cycling gloves has always been standard cycling equipment on any ride for me, whether on a short ride or a...
Hi Peter, hi Flevofans! ... Is that a general opinion about gripshift(like) shifters? If yes it might help to maintain your shifter cables. I have Sram...
... That's what I thought too, but then the leather gloves crumple and get hard, and one day it's almost impossible to put them on. I radically changed back to...
... It wasn't, and isn't that! Of course lubricating was the first I did. At home, with dry hands, it felt like I could change gear by blowing at the handle. I...
Hello all of you. For about ten years I was dreaming of having my own racer. Last week i orderd my framekit at the Tempelman store in Dronten. I already have a...
Hello Flevofans, today I received a message from the Cultureel Centrum Corrosia in Almere (NL). I'll try to translate their mail for you, but you'll find the...
You mean this one? http://www.ihpva.org/com/Flevo/flevo.green.jpg I believe the work on this prototype started many years ago, I even thought the project had...
... _Perhaps_ the _first commerical_. I only say Clemens Bucher/Berlin:-) Sincerely, Olaf -- Olaf Schultz Heimfelder Straße 77 21075 Hamburg Festnetz: 040 791...
Olaf Schultz
o.schultz@...
Nov 23, 2005 7:50 pm
510
... Only the one I found at the website of the organizer of the exhibition: http://www.corrosia.nl//ccc.html?section=ccc)#=NL Greetings, Martin...
Hi, To begin with recumbent bike i'm looking for a budget flevo road/race bike to restore or modify as i'm too short on time for building one from scratch. I...
François BOUQUIN
f.bouquin@...
Dec 3, 2005 10:42 am
512
Does anyone have the name of a manufacturer and part number for the diabolo (or part with eqivalent function) available in the U.S.?...
... I don't have special numbers or manufacturer names, but it seems that you can best try to ask for it in shops where they sell windsurfing parts. This kind...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
