Ok, I've been autocrossing occasionally since I was 16. I've wanted to get serious for 11 years. This looks like the best way to do that. But.... I'm having...
... Here's an example of what a used kart package can cost: http://www.ekartingnews.com/viewtopic.php?t=55212 Between $3500 and $5000 should get you a complete...
MRP is southwest of South Bend, and they do have a rental program. The problem is that most weekends are booked by various clubs. Always check before you go...
Hey Bob, What happened to the track in western Michigan, formerly the MRP HQ? Is it still operating, with a different group? Alan In a message dated 3/5/2007...
So far, for the 3 seasons I've been running F125, I've replaced the piston ring, bearing, pin, circlips and gaskets at the start of every season (along w/...
3 seasons road/sprint racing (about 30 hours), did not even pull the head. It has to be time to look at ti I guess. Somewhat built CR125 with RS piston...
Ok, so after JB Weld hasn't been holding, I'm starting to look into my options to replace my bottom end. There's a crack that goes from reed cage and swoops...
Ok, so after JB Weld hasn't been holding, I'm starting to look into my options to replace my bottom end. There's a crack that goes from reed cage and swoops...
I've posted a couple of pics in the photos section showing testimony to how tuogh the gearbox of a CR125 really is. I thought I'd share this with everyone just...
well I said last year I'd get a kart once I found a decent deal. I found a 01 CRG (not sure of the model) with a 01 Yamaha yz125 on it with light use. Runs...
Glad to hear there is another person running karts in Texas. 40-23: to 1 on the oil is good. the motor will last longer with 32:1 Now this is sometimes hard to...
Those are just pieces of aluminum i cut up and put between the rear hub and bearing to adjust my track. I made a few different sizes and even marked them with...
AJ Nealey Racing Hello! I have decided to try and keep people updated with my racing. Just completed my first race weekend with my newly acquired 1988 Honda...
about 1/3 of an inch on each side. eyeball it. If you have axle sprocket that is made of two halfs make sure you measure the slack all the way around the...
how hard is this? I'm looking for metal shards and I'm checking over the whole motor now that I am replacing the piston and ring (and all the little bits with...
Strange you should ask this at this time because i just replaced a crank in my cr125 and having someone that has done it before was a real help. Think i could...
Sounds like a Yamaha power valve plug job to me. And if its a Yamaha that is a common thing to find. It works good with the Yamaha's. Would not suggest doing...
Regarding the ring, I think what you'd find upon close examination is that the piston started to stick and either collapsed onto the ring groove, or aluminum...
So I'm trying to find out how to join F125 at Yahoo groups. I'm already a member but am trying to find out how some one new joins "F125"? A search of yahoo...
Simple. Click this link. http://sports.groups.yahoo.com/group/F125/join I think the reason the F125 group does not show up in the search is because of all the...
Moderator here! http://groups.yahoo.com/group/F125 is the link to use for the group. So, one thing that I proud myself on is that the F125 list is SPAM free....
Tom Harrington
tomh@...
Apr 17, 2007 11:38 pm
5020
Hey all just posted some photos of a kart rack / hauler that fits in the back of a F-150. I just finished the major fab work and need to finish the paint. but...
I'm having a really hard time finding the correct rotor for my rear brake. It's a Freeline caliper and mount. The rotor is a very odd size. 200mm OD, 145mm...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
